LM3911 DATASHEET PDF

LM Datasheet PDF Download – LM Temperature Controller, LM data sheet. (1) For all available packages, see the orderable addendum at the end of the datasheet. Basic Temperature Sensor Simplified Schematic. Calibrated Sensor. 1 . LM National Semiconductor datasheet pdf data sheet FREE Datasheets ( data sheet) search for integrated circuits (ic), semiconductors and other electronic .

Author: Mozilkree Faegis
Country: Spain
Language: English (Spanish)
Genre: Sex
Published (Last): 5 July 2006
Pages: 343
PDF File Size: 2.60 Mb
ePub File Size: 7.82 Mb
ISBN: 454-5-89145-540-5
Downloads: 2257
Price: Free* [*Free Regsitration Required]
Uploader: Tole

All of the components have already been mounted on the board and the board has been tested. Now that the probe is electrically attached to the cable, it is necessary to mechanically secure the probe and wire into the sensor housing.

Your temperature sensor is datashewt ready to be calibrated and put into datashert. If you no longer have the original manual, we have replacement manuals available for some kits at: This will take a couple of hours.

All that remains is to attach the new board to the old cable, and seal the completed assembly with silicon seal. Make certain that there is a good attachment of the silicon seal to the existing cable. T O e Temperature for zero output K.

PDF LM3911 Datasheet ( Hoja de datos )

I H e High temperature output current A. The LM uses the difference in emitter-base voltage of. LM to the temperature souce The LM is rated for. Set output to read C.

  GLISEMIK INDEKS TABLOSU PDF

Note 3 Either V b or V a can be ground. The output voltage of the LM is directly proportional to. The remaining 6 inches can be used to re-attach the old probe, should you feel it necessary for trouble shooting or whatever reason. The input bias current is low and relatively constant with.

Datasheets search archive of electronic components datasheets

Sealing the assembled temperature sensor in the tube. Selected as for meter thermometer except T O should. Y Uncalibrated accuracy g 10 C. The circuit was taken directly from the National LM datasheet. Temp Sensor board attached to old cable end.

Dahasheet With Meter Output. Y Internal op amp with frequency compensation. Original Heathkit sensor top and new replacement unit below. T O e Meter zero temperature K.

Ground Referred Centigrade Thermometer. Assembled and Tested Temperature Sensor. This should create a water-tight seal. The LM was a single chip that would output a 10 mV change for every degree of change in temperature.

Trims out initial lm3191 tolerance. Y Internal stable voltage reference. Note 1 C1 determines proportioning frequency f. The Heathkit part number of the module was typically a or a To begin the assembly it will be necessary to remove the old sensor by cutting the existing cable approximately 6 inches from the existing sensor.

  ENTREVISTA DE JAMES CREELMAN A PORFIRIO DIAZ PDF

Stand the probe on end and allow all of the silicon seal to cure completely. D T e Meter temperature span K. V z e Shunt regulator voltage use 6 Y Output can drive loads up to 35V. Select I Q s R1. Unfortunately the LM is no longer available and even small quantities have disappeared from surplus dealer’s and distributor’s shelves.

Follow the calibration instructions for your particular kit. Output goes negative on. The 0 01 in the above and following equations is in units of V K or V C and is a result of the basic 0 01V K sensitivity of the transducer. Datashheet active shunt regulator is connected across the power.

The 0 01 in the above and following equations is in units of V K or V C.

Meter Thermometer With Trimmed Output. Letting it stand overnight is best.

LM Hoja de datos ( Datasheet PDF ) – LM Temperature Controller

Y Can be calibrated in degrees Kelvin Celsius or. The LM is available in two package styles a metal can. I M e Meter full scale current A. V z e Shunt regulator voltage.

VPN