This guide has been released to the DRBD community, and its authors The DRBD User’s Guide v. Pacemaker CRM configuration. This document will cover the basics of setting up a third node on a standard Debian Etch installation. At the end of this tutorial you will have a DRBD device that. There may be multiple resource sections in a single file. For more examples, please have a look at the DRBD User’s Guide.
|Published (Last):||14 February 2009|
|PDF File Size:||5.4 Mb|
|ePub File Size:||17.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
During online verification as initiated by the verify sub-commandrather than doing a bit-wise comparison, DRBD applies a hash function to the contents of every block being verified, and compares that hash with the peer.
This can result in data loss or corruption. DRBD detected a split brain situation but remains unresolved. Wait for connection timeout, drhd this node was a degraded cluster. During resync-handshake, the dirty-bitmaps of the nodes are exchanged and merged using bit-orso the nodes will have the same understanding of which blocks are dirty.
If the decision is to discard the data on the primary node, call 8.3 pri-lost-after-sb handler on the primary node. The default value is ms, the default unit are tenths of a second. Wait for connection timeout. By default this is not gude. This section is a shortcut to define many connections which share the same network options. This also holds true for dumpe2fs 8 and similar commands. The stacked-timeouts parameter tells DRBD to use the wfc-timeout and degr-wfc-timeout parameters as defined in the configuration, even on stacked devices.
See the disk-flushes parameter. In this case, any start-sector see below will be ignored, and any stop-sector see below will be honored.
If drbd-proxy is used, it usdr advised to use c-delay-target instead of c-fill-target. With many usage patterns, a significant number of those blocks will actually be identical.
Configures a DRBD resource. Peer nodes need to wait until they receive an peer-ack for releasing a lock on an AL-extent.
The default unit is bytes. The helper program is expected to reboot the machine, which brings the node into a secondary role. If no name is specified, the peer’s host name is used instead. The default values of these parameters are: The handler is supposed to reach the peer over an alternative communication path and call ‘ drbdadm outdate minor ‘ there.
The stop-sector may be updated by issuing an additional drbdsetup verify command on the same node while the verify is running. Resync only progresses if neither the local nor the remote pause flag is set. We would debd to ask users to participate in the online usage counter as this provides us valuable feedback for steering the development of DRBD. This feature is only available to subscribers.
(5) — drbd-utils — Debian unstable — Debian Manpages
This section must contain a hosts parameter, which has the host names as arguments. Note the resource is data-upper and the –stacked option is on alpha only. A virtual IP is needed for the third node to connect to, for this we will set up a simple Heartbeat v1 configuration.
The disk state advances to diskless, as soon as the backing block device has finished all IO requests. This option defines the hash algorithm being used for that purpose.
Auto sync from the node that touched more blocks during the split brain situation. Replication among the devices in a resource takes place in chronological order. With this option you request that the automatic after-split-brain policies are used as long as the data sets of the nodes are somehow related.
That means it will slow down the application that generates the write requests that vrbd DRBD to send more data down that TCP connection. Usually this should be left at its default. May be up to 64 characters.
You are strongly encouraged to use peer authentication. That means it will slow down the application that generates the write requests that cause DRBD to send more data down that TCP connection. See the gujde on no-disk-flushes. By use, csums-alg is unset. Never access such a device while DRBD is running on top of it. The common section might have a startupa syncera handlersa net and a disk section. No, create an account now. It is essential that the node identifiers in the configuration and in the device metadata are changed consistently on all hosts.